Roadtrekking in our 210P via Lily Pads

This is our Trek in our Roadtrek 210P. Hint: Scroll to a list of "Topics and Destinations" on the right. Our RT is a portal to a much larger world and we have established "lily pads" from which we travel and we'll post about those, too. Life is a Journey of discovery in our Motorized Alpaca, a "tiny cabins on wheels". It has been said that "Life Begins at the end of our Comfort Zone." Content and photos are original unless noted. Click photos to enlarge. Copyright and disclaimers apply.

Monday, June 25, 2018

Repair of the Continental Tire Carrier on a 2012 Roadtrek 210P

Bruce Roberts has a 210P and discovered that the steel cable on his rear tire carrier was frayed. He had read my blog and had some questions about my February 27, 2017 blog post about repainting my tire carrier. So he contacted me via email.

Bruce had contacted Roadtrek about the possibility of repair. Bruce says that Roadtrek offered to sell a complete unit, but did not offer a repair. So Bruce decided to explore repairing it on his own. We corresponded about potential issues if a repair was undertaken. Bruce had a local firm that could fabricate the necessary cable, so the real issues were about disassembly and re-assembly.

The local firm could give him a replacement cable "made to order" to match the existing. Not too difficult if one can remove the old and give it to someone to match so the length and cable diameter is proper.

So Bruce proceeded with the repair and he had success. I asked Bruce if he would be willing to share his experience and he said "yes". Here is what he said about this "This is our first RV. We had never camped. Most of what I know about the RT is from reading blogs. I think it is important to give back something, so I am glad that you suggested writing a blog about repairing the carrier."

Thanks, Bruce for sharing your knowledge and experience with us in the RT community.

Here are Bruce's notes and some photos he put together about the repair. He agreed to let me share them here:

"Below are miscellaneous thoughts/comments concerning disassembly and reassembly of
the tire carrier. They are in no particular order. My cable was frayed and needed to be replaced.

One end of the cable is attached to the tension spring and is not designed to be separated.
All of the tension can be removed from the spring by backing down the spring tension bolt.
The cable can’t be removed from the assembly without removing the pulleys first.
The spring is under the least tension when the tire is upright in its normal position.
Two of the three pulleys have spacers on either side.
The pulley without spacers is smaller than the other two pulleys.
The carrier is designed to have the pulleys rotate freely.
The cable can fray if the pulleys don’t rotate.
The bolts associated with the cable and pulleys are grade 5 and the nuts have nylon inserts.
The smaller pulley is located at the hinge point for the two tubular pieces. There are 4 flat washers on the bolt that holds this pulley.
The cable on my unit was 26 ½ inches long and was 3/32 inches in diameter.
The carrier was removed from the RT prior to disassembly.

Disassembly sequence after removal from RT

Make notes concerning the distance between the top of each nut and the end of the bolt.
Lay the carrier on a flat surface and remove all tension from the spring by backing down the tension adjustment bolt at the top end of the carrier. A 19 mm socket was used on all bolts and nuts including removing the carrier from the RT.
Remove the bolt that holds the free end of the cable. Remove the pulleys starting with the one closest to the free end of the cable. Keep associated bolt, pulley, nut, and spacers/washers together. (On my unit, the smaller pulley was stuck on the bolt. I first tried tapping the end of the bolt with a hammer and piece of wood. That didn’t work. I sprayed lubricant on the bolt beside the pulley and tapped it again. That still didn’t work. I slid the handle of a socket wrench down beside the pulley and tapped it again. This time it worked. Prior to using the socket handle, only the top edge of the pulley was touching the notched portion of the square tubing and perhaps cocking the pulley as I tapped on the end of the bolt.)
Remove the nut on the tension adjustment bolt and remove the cable, spring, and tension adjustment bolt assembly.
Clean bolts, pulleys, nuts, and spacers and inspect for wear.
Clean the cable, spring, and tension adjustment bolt assembly and inspect for wear. Clean and repaint the two square tubing pieces as needed.

Reassembly sequence

The carrier was laid flat on a piece of cardboard with the three studs that hold the spare tire facing upward. Garage door spring lubricant was used to coat the spring.

Insert spring and cable assembly into the long section of square tubing and install the nut used to adjust the spring tension. Three turns on the nut were sufficient to keep the spring in place. To aid in the installation of the spring and cable assembly, a plastic garden stake was inserted into the square tubing. The spring tension adjustment bolt was butted up against the end of the garden stake and a small piece of duct tape was used to hold the pieces together. The other end of the garden stake was pulled while the spring and cable assembly was pushed into the square tubing.
Install the smaller pulley. The short section of square tubing was properly aligned and the cable was held in place with a clothespin. Lithium grease was sprayed on the bolt and pulley before and after installation. A cable tie strap was wrapped around the pulley to help hold the pulley while the bolt was inserted through the tubing. The tie strap wasn’t clamped to the pulley; it was just wrapped around it. Note there are four flat washers associated with this bolt. The nut was tightened enough to allow the short section of tubing to still pivot freely.
Install the next pulley in line. Lithium grease was sprayed on the bolt and pulley before and after installation. A cable tie strap was wrapped around the pulley and second spacer to help hold them while the bolt was inserted through the tubing. The cable was held in place with a clothespin. Insert the bolt part way and slide on the first spacer. Hold the pulley in place with the cable tie and insert the bolt so that it is flush with the other side of the pulley. Hold the second spacer in place with the cable tie strap and push the bolt through the other side. Install nut and tighten. Check for free rotation of the pulley. Tighten the nut until the pulley binds and loosen the nut about 1/8 turn.
Install the last pulley. Follow the same procedure used for the previous pulley.
Inspect the cable to ensure it is in the pulleys. Adjust the cable if has come off of a pulley.
Lift the short section of tubing upward so it is upright.
Secure the free end of the cable and the catch plate to the carrier. Tighten the nut until the catch plate binds and then loosen the nut about ¼ turn. Spray bolt with lithium grease.

Bruce's Notes :

The carrier should be inspected and lubricated periodically, but I don’t know how often. It will depend on usage and weather conditions.
The pulleys need to rotate freely.
There is a few thousands play between the pulley and spacers so additional lubricant can be added at a future time without having to disassemble the carrier.
This is our first RV. We had never camped. Most of what I know about the RT is from reading blogs. I think it is important to give back something, so I am glad that you suggested writing a blog about repairing the carrier.
The new cable cost $20.20."

Original material: https://roadtrek210.blogspot.com/

Friday, June 22, 2018

At the Beach, revisited

Well, the weather patterns changed and it has been about 25F cooler in recent days than it was over the weekend. With the change we've had near constant cloud cover and fog, as the rains approached. Love it when that warm gulf air meets a northern cold front. We've strolled the beaches, hunkered down a bit and I've been doing what I call "non-productive" work. That is work that generally doesn't generate income. These efforts include volunteer effort, blogging, reading financial and retirement articles, and doing business overhead matters. Never a dull moment.

The cooler weather has been pleasant, but with it the humidity has increased dramatically. The mosquitoes love this. We find that walking along the lake is a great escape, as the westerly breezes blow the little suckers inland. At the beach there is a bug free zone and those that do migrate toward the shore are tasty treats for the many swallows who constantly clean up the skies. At the pond we have dragonflies who carry out the same duties. In the past week I think I got one bite, which really isn't all that bad. We haven't had to use repellent yet this year.

Most of my internet related work is accomplished using a Verizon jetpack. It is not uncommon for campground internet to be intermittent. We've discovered this all over the U.S. So we use it when available and if it isn't, then out comes the jetpack. The jetpack is how I'm able to do this blog, upload videos, etc. If not for it, I'd be limited to email. In fact, yesterday I edited and uploaded the HOA newsletter. Not possible if not for the jetpack.